Home / BUILDER SERIES>FORD COMPATIBLE>MUSTANG DRESS / Ford Small Block Compatible 347 c.i. Engine and TKX Manual Transmission - 415 Horsepower - Mustang Edition Builder Series - Black Pulley Kit - Carbureted

Ford Small Block Compatible 347 c.i. Engine and TKX Manual Transmission - 415 Horsepower - Mustang Edition Builder Series - Black Pulley Kit - Carbureted

Quantity
ADD TO CART
BUY IT NOW
  • Detail
    • Detail

      Description:

      • Horsepower & Torque: 415 Horsepower / 415 ft. lbs. Torque
      • Compression Ratio: 10.0:1
      • Aluminum Heads
      • Cast Crank
      • Hydraulic Roller Cam

      Block:

      • BluePrint Engines High Strength Cast Iron Block
      • Increased Deck Thickness and Strength Webbing
      • Priority Main Oiling
      • 4.000" Bore
      • 4-Bolt Main
      • 1-Piece Rear Main Seal
      • Improved Water Jacket Design

      Rotating Assembly:

      • Cast Crank
      • 3.400" Stroke
      • Forged 5.400" Connecting Rods
      • Forged Pistons
      • 28oz Externally Balanced Front and Rear

      Cylinder Heads:

      • BluePrint Aluminum Cylinder Heads - HP9009
      • 60cc Chamber
      • 2.02" Intake / 1.60" Exhaust Valves
      • 190cc Intake / 60cc Exhaust Runners

      Cam Specs:

      • Hydraulic Roller Cam
      • .543 Intake / .554 Exhaust Lift
      • 218 Intake / 226 Exhaust Duration
      • @.050-112 Degree Lobe Separation

      Ignition Timing:

      • 34 Degrees Total at 3500 RPM

      Also Includes:

      • Holley Street Warrior 600cfm Vacuum Secondary Carburetor w/ Electric Choke
      • Mustang Style Valve covers *Mustang scripted valve cover may be different than pictured based on availability*
      • Front Accessory Drive with A/C Compressor, Power Steering, Alternator, and Water Pump
      • Thermostat and Thermostat Housing
      • Dual Plane, Satin Aluminum Intake Manifold
      • Pro Billet Distributor
      • 7 Quart Oil Pan
      • Electric Fuel Pump

      Assembled with Complete TKX Transmission Package:

      • Mcleod Super Street Pro Single Disk Clutch
      • Hydraulic Throw Out Bearing
      • Aluminum Bell Housing
      • Flywheel
      • Engine Guard
      • Starter
        • First Gear Ratio: 2.87:1
        • Second Gear Ratio: 1.89:1
        • Third Gear Ratio: 1.28:1
        • Fourth Gear Ratio: 1.00:1
        • Fifth Gear Ratio: 0.81:1

      Notes:

      • Package Ships assembled as pictured.
      • The front accessory drive on this engine fits many vehicles, however it is the customer responsibility to accurately measure and confirm fitment. Note this is a low-profile design, but things such as power steering hoses, alternator wiring, and additional fittings/fabrication may be required on some vehicles.
      • IF THIS IS BEING ORDERED FOR A FACTORY FIVE VEHICLE, STOP AND CALL US AT 1-800-483-4263 FOR PROPER FITMENT OR VISIT FACTORYFIVEENGINES.COM

    • Description
      This engine is designed and manufactured to factory specs for the specified vehicles below. It's manufactured using tighter machining tolerances, higher quality components, and finer balancing of the rotating assembly to make this engine better than the original while still meeting the description of a “replacement” engine.
    • Warranty

      The satisfaction of our customers is our highest priority at BluePrint Engines. We use quality components to balance your engine's rotating assembly within two grams of spec. We dyno test your crate engine and certify that it's ready to deliver horsepower and torque.

      We give your BluePrint engine the industry's best-in-class warranty for 30-months / 50,000 miles — with the extra confidence only BluePrint can provide. Our warranty applies to individual or professional installations and is fully transferable.

    • Notes
      • Designed as factory replacement long block for specified vehicles and year ranges, using OEM specification parts. Customer to re-use existing intake manifold, ecu (if equipped), exhaust, fuel system etc. Modification or replacement of provided tinware, and minor accommodations such as dipstick location may be required.
      • Specifically designed as an OEM spec engine to meet emissions requirements of the specified vehicles, to meet the criteria of "replacement engine" in all 50 states.
      • If your vehicle was originally equipped with a 2-piece rear main seal crankshaft, a new flex plate or flywheel will be required. Note for those same early applications, this block features the dipstick on the Passenger side.
      • Must verify with application list linked above for fitment.
    • Also Includes
      • New Valve Covers
      • Rear Sump Oil Pan
      • Timing Cover
      • Harmonic Balancer

      Recommended Break in Oil: BPP710 (Click Here)

      Recommended Service Oil: BPP10W30 (Click Here)

      Recommended Oil Filter: BPP51061 (Click Here)

    • Ignition Timing
      • OEM Specifications
    • Cam Specs
      • Hydraulic Flat Tappet
      • OEM Spec Per Listed Vehicles
    • Cylinder Heads
      • Perimeter Bolt Iron Cylinder Heads
    • Rotating Assembly
      • Cast Crankshaft
      • 3.480" Stroke
      • Forged 5.700" Connecting Rods
      • OEM Spec Pistons
      • Internally Balanced Front - Externally Balanced Rear Engine
    • Customer Reviews
      No comments
      SEE ALL
  • Customer Reviews
    No comments
BACK